Quick answer: A roll-down shutter motor is a 120-volt tubular motor that sits inside the roller tube in the shutter’s hood. To choose one, match four things: torque (50 Nm for lighter shutters, 100 Nm for heavier ones), control (a wall switch or a remote), whether you want a manual override crank for power outages, and the brand, EMS or Simu, because their parts, remotes and smart hubs don’t mix. If you are replacing a motor, the label on the old motor tells you most of this.
We sell 16 roll-down shutter motor kits, eight EMS and eight Simu, from $209 to $434, plus the Dooya and TaHoma smart hubs and an optional solar motor kit. This guide explains what the numbers on a shutter motor mean and how to pick the right one.
Roll-down shutter motors: key facts
- Every roll-down shutter motor we sell runs on 120 volts, 60 Hz, with an IP44 protection rating.
- 50 Nm motors lift about 150–246 lb (EMS) or 224–246 lb (Simu). 100 Nm motors lift about 256–386 lb (EMS) or 308–448 lb (Simu). These are the manufacturer’s theoretical lifting capacities, and they drop as shutter height increases.
- The solar motor kit comes in 30 Nm (up to 119 lb) and 50 Nm (up to 200 lb).
- Standard motors are 4-wire and run from a wall switch. Remote motors are 3-wire with a built-in radio receiver and come with a five-channel remote.
- Override motors have a crank eye, so you can raise or lower the shutter by hand when the power is out.
- EMS Brand motors are made by Dooya; Simu is part of the Somfy group. The two are not interchangeable. EMS remote motors work with the Dooya DD7002B smart hub; Simu remote motors work with the TaHoma 1811731.
- Motors run about 4–5 minutes at a time before built-in thermal protection stops them to cool.
What does Nm mean on a shutter motor?
Nm stands for newton-meters, the metric unit of torque: the twisting force the motor puts on the roller tube. It is not a weight rating. One newton-meter is about 0.74 pound-feet (8.85 inch-pounds).
| Motor torque | Pound-feet (lb-ft) | Inch-pounds (in-lb) |
|---|---|---|
| 30 Nm | 22.1 lb-ft | 266 in-lb |
| 50 Nm | 36.9 lb-ft | 443 in-lb |
| 100 Nm | 73.8 lb-ft | 885 in-lb |
Torque turns into lifting force where the shutter curtain leaves the roll. The farther that point is from the center of the tube, the less weight the same torque can lift:
Lifting force (lb) = torque (lb-ft) × 12 ÷ roll radius (inches)
For example, a 50 Nm motor makes 36.9 lb-ft. Where the curtain leaves the roll 2 inches from the center of the tube, that is about 221 lb of pull (36.9 × 12 ÷ 2). As the shutter rolls up, the roll gets fatter: at 3 inches, the same motor pulls about 148 lb. That is why a 50 Nm EMS motor is rated 150–246 lb instead of one number, and why the manufacturers note that lifting capacity decreases as shutter height increases. A taller shutter wraps into a bigger roll.
The formula leaves out friction in the side tracks, so use it to understand the ratings, not to size a motor. Size from the manufacturer’s lifting capacity, below, and leave room to spare.
How much weight can a 50 Nm or 100 Nm motor lift?
| Motor | Models | Speed | Theoretical lifting capacity | Continuous run time | Max limit turns |
|---|---|---|---|---|---|
| EMS 50 Nm | 449K, 423K, 445K, 446K | 13 rpm | 150–246 lb | 4 min | 22 |
| EMS 100 Nm | 510K, 529K, 528K, 527K | 11 rpm | 256–386 lb | 4 min | 22 |
| Simu 50 Nm | 449SK, 423SK, 445SK, 446SK | 12 rpm | 224–246 lb | 5 min | 28 |
| Simu 100 Nm | 510SK, 529SK, 528SK, 527SK | 14 rpm | 308–448 lb | 4–5 min | 22–28 |
| EMS solar 30 Nm | S346KB | — | Up to 119 lb | — | — |
| EMS solar 50 Nm | S446KB | — | Up to 200 lb | — | — |
Source: EMS and Simu motor specification charts in the EMS roll shutter catalog. “Max limit turns” is how many times the motor can turn the tube between its upper and lower stops; a taller shutter needs more turns. Among the Simu 100 Nm motors, the 510SK has 22 limit turns and the others 28, and the 510SK and 528SK run 4 minutes while the 529SK and 527SK run 5.
If your shutter falls near the top of a range, step up to the 100 Nm motor. An undersized motor works harder and reaches its thermal limit sooner.
How to size a roll-down shutter motor
- Buying a complete motorized shutter from us? You don’t need to pick a motor. When you order a motorized roll-down in our roll-down shutter pricing tool, we match the EMS or Simu motor to the shutter’s size and weight.
- Replacing a motor? Match the torque on the old motor’s label. The original motor was sized for that shutter, so the same Nm will lift it. The label also shows the brand and model; see the replacement checklist below.
- Adding a motor to a manual shutter, or not sure? You need the curtain weight: the slat weight per square foot × width × height, plus the bottom bar. The shutter’s manufacturer can give you the slat weight, or email us the slat size, width and height and we’ll tell you which motor fits.
- Check the motor length. The motor slides into the roller tube. Our motors run from 21.5 inches (EMS 449K) to 33.75 inches (Simu 527SK), so on a narrow shutter, make sure the tube is long enough for the motor.
Standard, override, remote or remote override?
Both brands make the same four types of roll-down shutter motor, in 50 Nm and 100 Nm.
| Motor type | Wires | How you run it | When the power is out | Smart hub ready? | EMS models | Simu models | Price range |
|---|---|---|---|---|---|---|---|
| Standard | 4 | Wall switch | No manual backup | With an add-on receiver | 449K, 510K | 449SK, 510SK | $209–$329 |
| Standard with manual override | 4 | Wall switch | Crank by hand | With an add-on receiver | 423K, 529K | 423SK, 529SK | $224–$416 |
| Remote | 3 | Five-channel remote (included) | No manual backup | Yes | 445K, 528K | 445SK, 528SK | $259–$434 |
| Remote with manual override | 3 | Five-channel remote (included) | Crank by hand | Yes | 446K, 527K | 446SK, 527SK | $271–$434 |
4-wire vs 3-wire. A standard motor has one wire for up, one for down, a neutral and a ground; the wall switch decides which way it turns. A remote motor has a hot, a neutral and a ground; up and down come by radio from the remote. Power to the motor should be run by a licensed electrician, following your local code.
Manual override. An override motor has a crank eye on its end. When the power is out, hook up a crank handle and wind the shutter by hand. Every complete motorized roll-down shutter we sell comes with an override motor and the crank handle. With replacement motor kits, the 5-foot crank handle with bell is sold separately ($74.99).
Remote-ready later. A standard motor can be switched to remote control with an add-on wireless receiver; EMS uses the DC74 receiver for its standard motors. Ask us which receiver fits your motor.
For how each control option works day to day, including switch types, crank positions and troubleshooting, see electric vs. manual roll down hurricane shutters.
EMS vs Simu shutter motors
Each EMS motor has a direct Simu equivalent with the same torque and type: 449K and 449SK, 423K and 423SK, 445K and 445SK, 446K and 446SK, 510K and 510SK, 529K and 529SK, 528K and 528SK, 527K and 527SK. Here is how the two brands differ.
| EMS | Simu | |
|---|---|---|
| Made by | Dooya | Simu, part of the Somfy group |
| Price (motor kit) | $209–$343 | $319–$434 |
| 50 Nm lifting capacity | 150–246 lb | 224–246 lb |
| 100 Nm lifting capacity | 256–386 lb | 308–448 lb |
| Speed | 13 rpm (50 Nm), 11 rpm (100 Nm) | 12 rpm (50 Nm), 14 rpm (100 Nm) |
| Rated power | 235 W (50 Nm), 340 W (100 Nm) | 210–250 W (50 Nm), 430 W (100 Nm) |
| Continuous run time | 4 min | 4–5 min |
| Max limit turns | 22 | 28 (22 on the 510SK) |
| Smart hub | Dooya DD7002B | TaHoma 1811731 |
| Extra remotes | EMS remotes | Simu Hz remotes, such as the Simu Hz 5-channel remote #2006143 |
Which should you pick? For a replacement, stay with the brand that is in the shutter now, so your remotes, hub and tube adapters keep working. For a new shutter, EMS costs less. Simu has the higher rated lifting capacity, most noticeably at 100 Nm, and its TaHoma hub connects to more smart-home systems.
The two brands use different parts: EMS lists its motors as not compatible with Simu motor products, and the Simu chart says the same about EMS. Don’t mix crowns, drives, brackets or remotes between brands.
Replacing a Dooya motor
EMS Brand motors are made by Dooya, which is why they work with the Dooya smart hub and Dooya receivers. If the label on your old motor says Dooya, the model code tells you which EMS motor replaces it. The letters after DM45 or DM59 give the type, and the numbers after the slash give the torque and speed: a DM45S 50/12 is a 50 Nm standard motor at 12 rpm.
| Dooya label | What it is | EMS replacement |
|---|---|---|
| DM45S | 50 Nm, standard (wall switch) | 449K |
| DM45M | 50 Nm, standard with manual override | 423K |
| DM45R | 50 Nm, remote (built-in radio receiver) | 445K |
| DM45RM | 50 Nm, remote with manual override | 446K |
| DM59S | 100 Nm, standard (wall switch) | 510K |
| DM59M | 100 Nm, standard with manual override | 529K |
| DM59R | 100 Nm, remote (built-in radio receiver) | 528K |
| DM59RM | 100 Nm, remote with manual override | 527K |
If your label shows a different torque, such as 30 Nm, ask us: EMS’s 30 Nm motors are special order. Dooya also makes 230-volt motors for markets outside the US, so check the voltage on any Dooya motor you buy elsewhere; every EMS Brand motor we sell is 120 volts.
Type 5 vs Type 6: tube size and what’s in the kit
The motor’s type tells you which roller tube it fits. Every 50 Nm motor we sell is a Type 5, and every 100 Nm motor is a Type 6.
- Type 5 (50 Nm) kits include 60mm and 70mm crowns and drives, so they fit a 60mm or 70mm octagonal tube.
- Type 6 (100 Nm) kits include a 70mm crown and drive and fit a 70mm octagonal tube.
Crown and drive. The crown is the adapter ring at the motor head that turns with the tube. The drive is the wheel on the motor’s output shaft that turns the tube. Both must match your tube’s size. Every kit also includes a mounting bracket, some include an alternate bracket, and remote kits include the five-channel remote; each product page lists exactly what’s in that kit.
Smart hubs: Dooya DD7002B vs TaHoma 1811731
A smart hub connects remote motors to your Wi-Fi, so you can open and close your shutters from a phone app or by voice. Each hub works with one brand only: the Dooya hub runs EMS motors because they are made by Dooya, and TaHoma is a Somfy product, so it runs Simu motors.
| Dooya DD7002B Smart Hub | TaHoma 1811731 Smart Home Gateway | |
|---|---|---|
| Works with | EMS remote motors: 445K, 528K, 446K, 527K and the S446KB solar motor | Simu remote motors: 445SK, 528SK, 446SK, 527SK, plus any wireless Somfy or Simu receiver |
| Capacity | Up to 30 motors per hub | Up to 40 channels |
| Voice and smart home | Amazon Alexa, Google Assistant, IFTTT | Amazon Alexa, Google Assistant, SmartThings, Philips Hue, IFTTT |
| More than one home | One account covers up to 5 locations, 5 hubs per location and 3 guest users | Multiple devices can be joined for multi-zone control |
| Other | RS485 port for third-party home-automation systems | — |
| Price | $279 | $355 |
Standard wall-switch motors can’t join a hub on their own. Choose a remote motor, or add a receiver: the Dooya hub also works with EMS’s DC74 and DC136 wireless receivers.
Solar roll-down shutter motor
For an opening with no outlet or wiring nearby, we offer an optional solar power kit with our roll-down shutters. A small solar panel keeps a battery charged, so the motor needs no wiring to your home’s electrical system and no electrician. The kit is made by EMS:
- Motor: a Type 5 remote motor with manual override, either the S346KB (30 Nm, lifts up to 119 lb) or the S446KB (50 Nm, lifts up to 200 lb), with an 8-foot power cable and twist connection, 60mm and 70mm crowns and drives, a bracket and a five-channel remote.
- Solar panel kit (DD1538HK): a 24-inch solar panel with a rechargeable battery, a 2-foot power cable with twist connection, micro-USB charging, quick-mount wall brackets, hinged brackets and mounting hardware.
EMS recommends the solar kit for 40mm and single-wall roll shutters, which in our line means the 40mm and 63mm roll-downs. Mount the panel on the wall beside the shutter where it gets direct sun. If the battery runs low, charge it by micro USB or crank the shutter by hand with the override. The 50 Nm solar motor also works with the Dooya smart hub.
Replacing a roll-down shutter motor: checklist
- Brand. Read the label on the motor head. Replace EMS with EMS and Simu with Simu, so your remotes, hub and adapters still fit.
- Torque. Match the Nm on the label: 50 Nm or 100 Nm.
- Type. Count the wires: 4 wires means a standard (switch) motor, 3 wires means a remote motor. If the old motor has a crank eye on its end, choose an override model.
- Tube size. Measure the octagonal roller tube: 60mm or 70mm. In our line, only the 50 Nm (Type 5) motors fit a 60mm tube.
- Length. Make sure the new motor fits in the tube; motor lengths are in the table below.
- Remote and limits. A replacement remote motor comes with its own five-channel remote. The remote is paired and the upper and lower limits are set at installation, following the motor’s instructions.
Installation. For fixed-price quotes to install or replace a shutter motor, post your job free on Hurricane Handyman.
All roll-down shutter motors we sell
| Model | Brand | Type | Torque | Speed | Motor length | Wires | Lifting capacity | Price |
|---|---|---|---|---|---|---|---|---|
| 449K | EMS | Standard | 50 Nm (Type 5) | 13 rpm | 21.5" | 4 | 150–246 lb | $209 |
| 423K | EMS | Standard with manual override | 50 Nm (Type 5) | 13 rpm | 24" | 4 | 150–246 lb | $224 |
| 445K | EMS | Remote | 50 Nm (Type 5) | 13 rpm | 27" | 3 | 150–246 lb | $259 |
| 446K | EMS | Remote with manual override | 50 Nm (Type 5) | 13 rpm | 29.75" | 3 | 150–246 lb | $271 |
| 510K | EMS | Standard | 100 Nm (Type 6) | 11 rpm | 32.75" | 4 | 256–386 lb | $274 |
| 529K | EMS | Standard with manual override | 100 Nm (Type 6) | 11 rpm | 24.5" | 4 | 256–386 lb | $245 |
| 528K | EMS | Remote | 100 Nm (Type 6) | 11 rpm | 30.5" | 3 | 256–386 lb | $343 |
| 527K | EMS | Remote with manual override | 100 Nm (Type 6) | 11 rpm | 30.5" | 3 | 256–386 lb | $314 |
| 449SK | Simu | Standard | 50 Nm (Type 5) | 12 rpm | 23.625" | 4 | 224–246 lb | $319 |
| 423SK | Simu | Standard with manual override | 50 Nm (Type 5) | 12 rpm | 26" | 4 | 224–246 lb | $364 |
| 445SK | Simu | Remote | 50 Nm (Type 5) | 12 rpm | 26.5" | 3 | 224–246 lb | $364 |
| 446SK | Simu | Remote with manual override | 50 Nm (Type 5) | 12 rpm | 30.25" | 3 | 224–246 lb | $364 |
| 510SK | Simu | Standard | 100 Nm (Type 6) | 14 rpm | 27.125" | 4 | 308–448 lb | $329 |
| 529SK | Simu | Standard with manual override | 100 Nm (Type 6) | 14 rpm | 26.25" | 4 | 308–448 lb | $416 |
| 528SK | Simu | Remote | 100 Nm (Type 6) | 14 rpm | 28.75" | 3 | 308–448 lb | $434 |
| 527SK | Simu | Remote with manual override | 100 Nm (Type 6) | 14 rpm | 33.75" | 3 | 308–448 lb | $434 |
Prices are for the motor kit, as of November 2026. All motors are 120V, 60 Hz, IP44. Smart hubs: Dooya DD7002B ($279) and TaHoma 1811731 ($355). Shop all roll-down shutter motors.
Frequently asked questions
How much does a roller shutter motor replacement cost? A replacement roll-down shutter motor kit costs $209 to $434 from us as of November 2026: EMS kits run $209–$343 and Simu kits $319–$434. Standard wall-switch motors start lowest; remote and override models cost more. Installation and any electrical work are extra. For fixed-price installation quotes, post your job free on Hurricane Handyman.
What size motor do I need for my roller shutter? It depends on the shutter's weight. A 50 Nm motor lifts about 150–246 lb (EMS) or 224–246 lb (Simu); a 100 Nm motor lifts about 256–386 lb (EMS) or 308–448 lb (Simu), and capacity drops as shutter height increases. If you are replacing a motor, match the Nm on the old motor's label. If you don't know the weight, send us the slat size, width and height and we'll tell you which motor fits.
How do I replace a roller shutter motor? Start by matching the old motor: the same brand, so your remotes and hub keep working; the same torque in Nm; the same type (4-wire switch or 3-wire remote, with or without a crank eye); adapters for your 60mm or 70mm octagonal tube; and a motor that fits the tube's length. The swap means taking the roller tube out of the hood and reconnecting power, which should be done by a licensed electrician. For fixed-price quotes, post your job free on Hurricane Handyman.
How does a roller shutter motor work? A roller shutter motor is a tubular motor that slides inside the roller tube. Its drive wheel turns the tube, which rolls the slats up or lets them down, and built-in limits stop it at the fully open and fully closed positions. A standard motor runs from a wall switch; a remote motor has a radio receiver built in. Override models add a crank eye, so you can wind the shutter by hand when the power is out.
Why is my roller shutter motor not working? The usual causes are: thermal protection, which stops the motor after about 4–5 minutes of running until it cools; no power, so check the breaker; the remote, with a dead battery, the wrong channel or a remote that isn't paired; limits that are out of adjustment, so the shutter stops short; or debris in the side tracks. If none of these fix it, the motor may need replacing.
How is a roller shutter motor wired? A standard (wall-switch) motor has 4 wires: one for up, one for down, a neutral and a ground. A remote motor has 3 wires: hot, neutral and ground, with up and down sent by the remote. All of our motors are 120-volt, 60 Hz. Have a licensed electrician make the connections, following your local code.
Can I add a remote to my roller shutter motor? Yes. Our remote motors come with a five-channel remote, so one remote can run several shutters, each on its own channel. A standard wall-switch motor can be made remote-ready with an add-on wireless receiver (EMS uses the DC74 for its standard motors), or you can replace it with a remote motor of the same brand and torque.
How do I program a Simu remote? Follow the instructions that come with your Simu motor: you pair the remote to the motor, then set the upper and lower limits. The exact button sequence depends on the motor model. If you have lost the instructions, contact us with your order number and we'll send them. Extra Simu remotes, such as the Simu Hz 5-channel remote #2006143, pair the same way.
What is the Dooya smart hub? The Dooya DD7002B smart hub, also called the Dooya smart bridge or Wi-Fi bridge, connects EMS remote motors (445K, 528K, 446K, 527K and the S446KB solar motor) to your Wi-Fi, so you can run your shutters from the phone app or with Amazon Alexa, Google Assistant or IFTTT. One hub handles up to 30 motors and costs $279. For Simu motors, use the TaHoma 1811731 ($355) instead.
Do solar powered roller shutters work during a hurricane? Yes. The solar motor runs from a rechargeable battery that the solar panel keeps charged, so it does not depend on house power. If the battery runs low, you can charge the panel by micro USB or crank the shutter by hand, because the solar motor has a manual override.
What does Nm mean on a shutter motor? Nm stands for newton-meters, the unit of torque: the twisting force the motor puts on the roller tube. It is not a weight rating. One newton-meter is about 0.74 pound-feet, so a 50 Nm motor makes about 36.9 lb-ft and a 100 Nm motor about 73.8 lb-ft. How much that torque can lift depends on the size of the roll, which is why every motor has a lifting-capacity range.
How much weight can a 50 Nm or 100 Nm shutter motor lift? A 50 Nm EMS motor has a theoretical lifting capacity of 150–246 lb, and a 50 Nm Simu motor 224–246 lb. A 100 Nm EMS motor lifts 256–386 lb, and a 100 Nm Simu motor 308–448 lb. The 50 Nm solar motor lifts up to 200 lb and the 30 Nm solar motor up to 119 lb. Capacity drops as shutter height increases, so if your shutter is near the top of a range, step up to the next size.
Do I need a manual override shutter motor? If you need to open or close the shutter when the power is out, yes. An override motor has a crank eye, so you can wind the shutter by hand with a crank handle. Every complete motorized roll-down shutter we sell comes with an override motor and the crank handle; with replacement motor kits, the crank handle is sold separately.
Are EMS shutter motors made by Dooya? Yes. EMS Brand roll-down shutter motors are made by Dooya, which is why they work with the Dooya DD7002B smart hub and Dooya receivers. To replace a Dooya motor, match its label: DM45S = 449K, DM45M = 423K, DM45R = 445K, DM45RM = 446K (all 50 Nm), and DM59S = 510K, DM59M = 529K, DM59R = 528K, DM59RM = 527K (all 100 Nm). Every EMS Brand motor we sell is 120 volts.
Can I replace an EMS shutter motor with a Simu motor? Every EMS motor has a Simu equivalent with the same torque and type (for example 449K and 449SK), but the two brands do not share parts, remotes or smart hubs. Replacing a motor with the same brand is the simplest swap. If you change brands, use the new motor's own crowns, drives, bracket and remote, and note that a Dooya hub will not control a Simu motor and a TaHoma hub will not control an EMS motor.
Which smart hub works with my roll-down shutter motor? EMS remote motors (445K, 528K, 446K, 527K and the S446KB solar motor) work with the Dooya DD7002B smart hub. Simu remote motors (445SK, 528SK, 446SK, 527SK) work with the TaHoma 1811731. Each hub works with its own brand only, and standard wall-switch motors need an add-on receiver before they can connect to a hub.
How long can a roll-down shutter motor run? About 4 to 5 minutes of continuous running. After that, built-in thermal protection stops the motor so it can cool down. Let it rest, then run it again; if you are closing many shutters, run them one at a time.
What voltage are your roll-down shutter motors? All 16 of the roll-down shutter motors we sell are 120-volt, 60 Hz motors for standard US household circuits, rated IP44.
Can you get a roll-down shutter motor you don't list? Usually, yes. Our supplier can source most roll-down shutter motors, including special-order EMS 30 Nm and 300 Nm models, other Simu motors and controls, and motors from brands such as Somfy, Becker, Elero, Nice, Gaposa, Dooya and Alutech. Send us the brand and model number from the motor's label, the torque and your shutter's size, and we'll reply with availability and price.
Need a motor we don’t list?
Our supplier can source most roll-down shutter motors, so if you need something other than the 16 kits above, ask us. Popular motors you can request include:
- EMS 30 Nm motors for small, light shutters (theoretical lifting capacity 134–148 lb): the 349K standard, 323K standard with override, 345K remote and 346K remote with override. These are special-order models.
- EMS 580K, a 300 Nm override motor for very large, heavy shutters (theoretical lifting capacity 760–1,015 lb; not UL listed).
- Other Simu motors and Simu Hz controls, such as 16-channel and keychain remotes, wall-mounted transmitters and receivers.
- Other motor brands, such as Somfy, Becker, Elero, Nice, Gaposa, Dooya and Alutech.
Send us the brand and model number from the motor’s label (a photo of the label works too), the torque in Nm and your shutter’s width and height, and we’ll get back to you with availability and price. Send us a motor request, email info@hurricaneshutterswholesale.com or call 561-626-8708.
Ready to buy? Shop roll-down shutter motors, or price a complete motorized roll-down shutter with the motor already matched to it.